stingerz
Oud Maniac
Posts: 64
Registered: 11-20-2009
Member Is Offline
Mood: happy
|
|
string action
hi guys....how r u guys doin? hp all is well...
i wanna know how do i reduce my string action on my egypt oud...how i wish oud comes with a truss rod!!
first of all i was thinkin of takin d bridge out and sand it till it s d right height but i m afraid tt i will destroy the paint work on d face of d
oud..... or can i jus make another hole at b bridge? jus below d existin 1?so tt d string goes "in" a new hole..
pls advise...
|
|
|
Franck
Oud Junkie
Posts: 145
Registered: 8-21-2007
Location: Montréal, Québec
Member Is Offline
Mood: No Mood
|
|
Drilling new holes will help, but be careful not get your string to close to the soundboard.
You could also sand the fingerboard near the nut if you have enough thickness to do so.
Another (more drastic) way is to saw the neck where it joins the body (you don't saw it off but about halfway through from the bottom of the oud).
Then you glue it back so the gap you created with the saw (be it a fret saw, not too thick) will bring back the action a little lower (kind of like
what a truss rod would do). You should let a luthier deal with this procedure.
Good luck
|
|
|
Luttgutt
Oud Junkie
Posts: 578
Registered: 1-10-2009
Location: Norway
Member Is Offline
Mood: Curious
|
|
This discussion is currantly going on here
http://www.mikeouds.com/messageboard/viewthread.php?tid=10130
Welcome to the forum
The wood might be dead, but the oud is alive.
|
|
|
fernandraynaud
Oud Junkie
Posts: 1865
Registered: 7-25-2009
Location: San Francisco, California
Member Is Offline
Mood: m'Oudy
|
|
Yes, this is an ongoing problem for ouds with no neck adjustment. What it's coming to is that there are several ways to drop the action a small
amount, you can use several methods at once, or just one, say lowering the holes in the bridge. One one of the least destructive ways we are thinking
about is to get a little board of hard wood and make a fingerboard that tapers towards the nut and glue it on top of the existing fingerboard.
|
|
|
stingerz
Oud Maniac
Posts: 64
Registered: 11-20-2009
Member Is Offline
Mood: happy
|
|
i was thinkin.... mayb the oud is made in tt way? cos the person who does the oud would know better i guess....
i was thinkin of sawing the neck thru , then i ll pun some rose wood or walnut wood under neath the neck and i ll put d existin neck on top of it and
put some wood glue but i guess the wood would be super thin...a super thin plank of rosewood ?..so i will nt hav to drill a hole on d bridge...is it
possible?
|
|
|
fernandraynaud
Oud Junkie
Posts: 1865
Registered: 7-25-2009
Location: San Francisco, California
Member Is Offline
Mood: m'Oudy
|
|
I guess. I'll leave such complicated woodwork to you experts. Me, I'm working on an adjustable neck, you can see it in prototype form below. The
astute observer will note the microcontroller circuit board between the Formica resonator and the neck pull-rods. The fingerboard will be reinstalled
as soon as we can find a place for it.
|
|
|
Sazi
Oud Junkie
Posts: 786
Registered: 9-17-2007
Location: Behind my oud
Member Is Offline
Mood: مبتهج ; ))
|
|
 Does that control the onboard mic simulator and octave divider as well?
Just replace it with an accelerometer-controled note generator and a ribbon controller...
|
|
|
![[*]](images/xmbprobrown/default_icon.gif){kind=icon}
